Uranium enrichment (43222)Посмотреть архив целиком
Federal Agency of Higher Education
Tomsk Polytechnic University
Applied Physics and Engineering Faculty
Student of group 0850
1. Uranium Enrichment – Introduction
There is one element that occurs in nature that has been the raw material for nuclear bombs: uranium, chemical symbol U. Uranium occurs in nature as a mixture of three different isotopes – that is, three different atomic weights that have virtually the same chemical properties, but different nuclear properties. These isotopes are U-234, U-235, and U-238. The first is a highly radioactive trace component found in natural uranium, but it is not useful in any applications; the second isotope is the only fissile material that occurs in nature in significant quantities, and the third is the most plentiful isotope (99.284 percent of the weight of a sample of natural uranium is U-238), but it is not fissile. U-238 can, however, be split by high energy neutrons, releasing large amounts of energy and is therefore often used to enhance the explosive power of thermonuclear, or hydrogen, bombs.
Because of the presence of small quantities of U-235, natural uranium can sustain a chain reaction under certain conditions, and therefore can be used as a fuel in certain kinds of reactors (graphite-moderated reactors and heavy water3 reactors, the latter being sold commercially by Canada). For the most common reactor type in use around the world today, which uses ordinary water as a coolant and moderator, the percentage of U-235 in the fuel must be higher than the 0.7 percent found in natural uranium. The set of industrial processes that are used to increase the percentage of U-235 in a given quantity of uranium go under the general rubric of “uranium enrichment” – with the term “enrichment” referring to the increase in the percentage of the fissile isotope U-235. Light water reactors typically use 3 to 5 percent enriched uranium – that is, the proportion of U-235 in the fuel is 3 to 5 percent, with almost all the rest being U-238. Material with this level of U-235 is called “low enriched uranium” or LEU.
Nuclear bombs cannot be made from natural or low enriched uranium. The proportion of U-235, which is the only one of the three isotopes that can sustain a chain reaction in uranium, is just too small to enable a growing “super-critical” chain reaction to be sustained. Uranium must have a minimum of 20 percent U-235 in it in order to be useful in making a nuclear bomb. However, a bomb made with uranium at this minimum level of enrichment would be too huge to deliver, requiring huge amounts of uranium and even larger amounts of conventional explosives in order to compress it into a supercritical mass. In practice, uranium containing at least 90 percent U-235 has been used to make nuclear weapons. Material with this level of enrichment is called highly enriched uranium or HEU. The bomb that destroyed Hiroshima on August 6, 1945, was made with approximately 60 kilograms of HEU. Highly enriched uranium is also used in research reactors and naval reactors, such as those that power aircraft carriers and submarines. The HEU fuel meant for research reactors is considered particularly vulnerable to diversion for use in nuclear weapons.
Thorium-232, which is also naturally occurring, can be used to make bombs by first converting it into U-233 in a nuclear reactor. However, uranium fuel for the reactor, or fuel derived from uranium (such as plutonium) is needed for this conversion if U-233 is to be produced in quantity from thorium-232.
A fissile material is one that can be split (or fissioned) by low energy neutrons and is also capable of sustaining a chain reaction. Only fissile materials may be used as fuel for nuclear reactors or nuclear weapons. Examples of other fissile materials, besides uranium-235, are uranium-233 and plutonium-239.
“Heavy water” is water that contains deuterium in place of the ordinary hydrogen in regular water (also called light water). Deuterium has one proton and one neutron in its nucleus as opposed to hydrogen, which has only a single proton.
The same process and facilities can be used to enrich uranium to fuel commercial light water reactors – that is to make LEU – as well as to make HEU for nuclear bombs. Therefore all uranium enrichment technologies are potential sources of nuclear weapons proliferation. In addition, some approaches to uranium enrichment are more difficult to detect than others, adding to concerns over possible clandestine programs.
2.Uranium Enrichment technologies
Only four technologies have been used on a large scale for enriching uranium. Three of these, gaseous diffusion, gas centrifuges, and jet nozzle / aerodynamic separation, are based on converting uranium into uranium hexafluoride (UF6) gas. The fourth technique, electromagnetic separation, is based on using ionized uranium gas produced from solid uranium tetrachloride (Ucl4).
2.1 Gaseous Diffusion
The gaseous diffusion process has been used to enrich nearly all of the low and highly enriched uranium that has been produced in the United States. It was first developed in the 1940s as part of the Manhattan Project and was used to enrich a portion of the uranium used in the bomb that was dropped on Hiroshima. All five acknowledged nuclear weapons states within the nuclear non-proliferation treaty (NPT) regime have operated gaseous diffusion plants at one time or another, but currently only the United States and France continue to operate such facilities. The diffusion process requires pumping uranium in a gaseous form through a large number of porous barriers and, as noted above, is very energy intensive.
In order to make the uranium into a gaseous form that can be used in the diffusion process, the natural uranium is first converted into uranium hexafluoride (UF6). The uranium hexafluoride molecules containing U-235 atoms, being slightly lighter, will diffuse through each barrier with a slightly higher rate than those containing U-238 atoms. A simple analogy to help visualize this process is to imagine blowing sand through a series of sieves. The smaller grains of sand will preferentially pass through each sieve, and thus after each stage they would represent a slightly higher percentage of the total than they did before passing through the stage. A schematic representation of one such stage from a gaseous diffusion plant is shown in Figure 1.
Figure 1: Schematic diagram of a single stage in a gaseous diffusion plant.
The darker colors represent the UF6 molecules that contain the heavier U-238 atoms, while the lighter colors represent gas molecules that contain the lighter U-235. After each stage the gas to the low pressure side of the barrier (i.e. the downstream side) has a slightly higher percentage of U-235 than the stage before.
The difference in mass, and therefore velocity, between the UF6 molecules containing either U-235 or U-238 is very small, and thus thousands of such stages are needed in order to enrich commercial or military amounts of uranium. In a gaseous diffusion plant, the stages are arranged into “cascades” that allow each stage to build on the enrichment achieved by the ones before it and also to more efficiently make use of the depleted uranium stream. For a sense of scale, when it was first constructed in the early 1940s the gaseous diffusion plant at Oak Ridge, Tennessee, was the largest industrial building in the world. The facility at Oak Ridge is shown in Figure 2 while a picture of two of the diffusers used in the enrichment process is shown in Figure 3.
Figure 2: Oak Ridge gaseous diffusion plant, built during World War II.
At the time of its construction this was the largest industrial building in the world. In part it was decided to locate this plant in Tennessee so that its large electricity demand could be met by the abundant coal and hydroelectric plants built by the government run Tennessee Valley Authority. It is now closed and awaiting decommissioning.
Figure 3: A close up picture of the outside of two of the diffuser stages used at the Oak Ridge uranium enrichment plant.
The diffusers contain the porous barriers used to separate the lighter U-235 atoms from the heavier U-238 atoms. Connected to the diffusers is equipment to compress the uranium hexafluoride gas and pipe it through the cascade as well as equipment to remove the large amount of heat generated during the enrichment process. Each diffuser and compressor are together referred to as a “stage.”
The most challenging step in building a gas diffusion plant is to manufacture the permeable barriers required in the diffusers. The material for the barriers needs to be highly durable and able to maintain a consistent pore diameter for several years of operation. This is particularly challenging given the highly corrosive nature of the uranium hexafluoride gas used. Typical barriers are just 5 millimeters (less than 0.2 inches) thick and have openings that are only about 30 to 300 times the diameter of a single uranium atom.
In addition to requiring a large amount of electricity during operation, the compressors in the gas diffusion facilities also generate a great deal of heat that requires dissipation. In U.S. plants this heat is dissipated through the use of ozone depleting chlorofluorocarbons (CFCs) such as the coolant CFC-114 (often referred to simply as Freon of Freon-114). The manufacture, import, and use of CFCs were substantially restricted by the 1987 Montreal Protocol on Substances That Deplete the Ozone Layer, which the U.S. is implementing through the 1990 Amendments to the Clean Air Act. As a result of these commitments, the manufacture of Freon in the U.S. ended in 1995 and its emissions to the air in the United States from large users fell by nearly 60% between 1991 and 2002. The emissions from the Paducah gaseous diffusion plant, however, have remained virtually constant over this time, falling just over 7% between 1989 and 2002. In 2002, the Paducah enrichment plant emitted more than 197.3 metric tons of Freon into the air through leaking pipes and other equipment. This single facility accounted for more than 55% of all airborne releases of this ozone depleting CFC from all large users in the entire United States in 2002. Due to the lack of additional manufacturing of Freon since 1995, the U.S. Enrichment Corporation is currently looking for a non-CFC coolant to use. Likely candidates would still have heat trapping potential, and thus even if they were not as dangerous to the ozone layer, they would still remain a potential concern in relation to global warming and climate change.
Чтобы не видеть никакую рекламу на сайте, нужно стать VIP-пользователем.
Это можно сделать совершенно бесплатно. Читайте подробности тут.